JAMES AND MORRIS CAREY \ On the House Kit saves space that gets wasted by dryer duct

Brother Morris' wife, Carol, recently noticed a magazine ad for a stamp-formed metal device that looked a lot like a dishpan with a large round hole in one end. What she had spotted was a space-saving device that would change forever the way she would think about the laundry room.
Carol has been designing kitchens, baths, laundry areas and other remodeling and custom homes for nearly two decades. She couldn't wait to pass her discovery on to us. "This is one your readers should know about," she said. It's a device that allows a dryer to be installed against the wall -- no kidding! It lets you gain space in a tight laundry room.
In the past, we have always designed a laundry area to include a 3-feet-deep space for the dryer. Thirty-six inches might sound like overkill because most clothes dryers are between 24 inches and 27 inches. However, as longtime remodelers, we have found that most of the difference between the space provided and the dryer itself gets eaten up by the flex duct that connects the dryer exhaust to the wall outlet.
Variations in technique
For decades we have watched appliance manufacturers, ventilation contractors, architects, builders and remodelers struggle to solve the problem of what to do with the dryer ducting and how to save the space it typically wastes. We have seen many twists on dryer installation.
One solution is to connect the duct to the side of the dryer. It gets the dryer up against the back wall all right, but space to either side can be equally important. What difference does it make where the space is wasted?
Once, we were involved with an architect who concluded that the exhaust port in the wall had to exactly align with the outlet port in the back of the dryer. He handed us the specifications and told us that if the two ports were exactly aligned, the dryer could be fitted directly into the wall outlet and no space would be wasted. We assured him that we would position the wall outlet to his exact specifications. But at the last minute, the owner decided on a different brand of appliance. At that point we decided that the architect would be the one to install the dryer.
One dryer manufacturer offers an outlet port underneath its unit. Obviously, it is designed to accommodate some kind of floor connection. We are still waiting to see what kind of crane this manufacturer recommends to accomplish the installation.
What kit does
Enough of the pitfalls of dryer installation. What Carol discovered was an ad for a wall-mount recess kit called "The Dryerbox." It is a simple metal box that is designed to use the space in the wall cavity as a "recessed" collection point for your dryer's flex connection. Remember when they came out with the recessed wall box for the faucets and drain for a clothes washer? This is a similar kind of contraption, only it's used with a dryer.
Even with the best of inventions, there often are drawbacks. In our opinion, the shortcomings of The Dryerbox include:
UIt is designed to work only with dryer ducts that travel upward. Because many dryer connections are placed beneath the floor, this one might not be for you. Of course, this doesn't mean that you can't install a new in-wall duct that exhausts upward. It's a lot of work, but if space in your laundry area is critical, the extra cost might be worth it.
UThe dryer outlet and the stud cavity in which it resides must be situated so The Dryerbox can be located in alignment with the dryer's exhaust port. Because a flexible duct is the standard of installation, dryers rarely align perfectly with wall connections. This could require expensive framing modifications.
Something we noticed: Crimping and other types of ductwork gridlock can occur when the flex pipe is too long or not carefully managed as the dryer is pushed into position. Our advice here is to take it a little at a time.
Even with the minor obstacles we've mentioned, we think The Dryerbox is a groundbreaking invention and a space-saver of the highest order. Carol was right -- The Dryerbox does look like a dishpan. It is rectangular in shape (121/4 inches wide by 211/2 inches high) and it is mounted vertically into a single-stud bay. The exhaust duct in the wall enters the box through the top by way of a precut opening. A knockout is provided for a gas line.
Instructions for installing
Here's how to install one:
ULocate the studs on either side of your dryer duct. Because The Dryerbox is narrower than a typical stud bay, there is some latitude for side-to-side placement.
UCut out the wallboard using The Dryerbox as a pattern so it can be mounted onto one of the studs. At this point, additional blocking or backing can be added to the opposite side of the opening so the unit can be solidly attached on both sides.
UCut the exhaust duct so it will protrude 2 to 3 inches into The Dryerbox.
UInstall The Dryerbox using three to six screws.
UConnect the flex hose to the dryer and then to the exhaust duct.
UPush the dryer carefully into place. As you push the dryer slowly toward the flex duct, it will gently drop into the recess and should end up closer to the wall than before.
Again, keep in mind that The Dryerbox works only when the exhaust port on the dryer aligns with the exhaust duct in the wall (plus or minus an inch or two). If it doesn't, you will need to relocate your dryer or the duct (along with The Dryerbox) so they do.
XFor more home improvement tips and information, visit www.onthehouse.com on the Web.